RadiatorInhibitor.co.uk
£12.99 free delivery Amazon
Radiator inhibitor funnel

Inhibitor in. Every last drop. No mess.

No level pipe. No drips.

The elbow comes with its genuine Flomasta brass end fitted. Screw it into the plug port at the top of a radiator until it points straight up, screw the funnel on, and pour. The short elbow drops at about 38 degrees all the way into the radiator, so every drop goes in and nothing is left in it to drip when you take it off.

£12.99
Free tracked deliveryPosted in 2 working days
The black radiator inhibitor funnel: a wide funnel on an angled elbow ending in a brass radiator thread

Adding inhibitor to central heating

How to add inhibitor through a radiator

  1. Turn the heating offLet the radiators go cold. Pick one on the ground floor if you can, and put an old towel under it.

  2. Isolate the radiatorClose the valves at both ends: the one you turn to change the heat, and the lockshield under its plastic cap. Count the turns on the lockshield so you can set it back the same.

  3. Make roomOpen the bleed valve, then let a little water out of that radiator at a valve so there's space for the inhibitor. The rest of the system stays full.

  4. Fit the funnelUnscrew the blanking plug from the top corner. Put a few wraps of PTFE tape on the brass, screw the elbow in by hand until it points straight up (a spanner is optional), then screw the funnel on.

  5. Pour it inLeave the bleed valve at the other end of the radiator open, so air can get out and the inhibitor runs in without glugging. Pour steadily into the funnel. The elbow drops all the way, so none is left sitting in it.

  6. Put it back togetherTake the funnel off, unscrew the elbow, refit the plug, open both valves, bleed the radiator, and top the boiler pressure back up if the gauge has dropped.

Why the angle matters

Other dosing tools leave inhibitor in the pipe.

Most radiator dosing tools drop straight down, then turn a hard 90 degrees into a level pipe. Once the tool is screwed into the radiator you can't tip it, so the last of the inhibitor lies in that pipe behind the brass fitting. It stays there until you unscrew it, then runs down the radiator and onto the carpet.

Ours has no level pipe. The elbow drops at about 38 degrees all the way into the radiator, so gravity takes every drop in, and nothing is waiting to come out when you take it off.

The bend, side by side

Where the inhibitor actually goes

Cut-away side view of a usual 90 degree dosing tool: the inhibitor drops down the stem, turns into a level pipe and the last of it lies in the pipe behind the brass fitting.LEFT BEHIND
The usual 90° dosing toolThe last of the inhibitor lies in the level pipe and drips down the radiator when you take it off.
Cut-away side view of ours: a short elbow drops at about 38 degrees straight into the radiator, so every drop runs in and nothing is left behind.ALL IN
OursA short elbow drops about 38° all the way into the radiator, so every drop runs in.

What you get

Small tool, whole job

01

Short and tidy

12.6 cm tall from the elbow to the rim, so it fits under a window sill or shelf above the radiator, and the elbow packs inside the funnel for the drawer or the toolbag.

02

A 9 cm mouth

The funnel is 9 cm across and holds about 300 ml, so you pour into a wide mouth instead of aiming at a narrow tube.

03

Genuine brass

The thread into your radiator is a genuine Flomasta 1/2 inch BSP brass hexagon nipple, not a no-name fitting. It comes fitted to the elbow, ready to screw into the radiator by hand, with a spanner optional.

04

Points straight up

Put a few wraps of PTFE tape on the brass and screw the elbow in until it is snug and the socket points straight up. The funnel then screws straight on.

38°Drop into the radiator
9 cmAcross the mouth
300 mlIn the funnel
1/2"Brass BSP thread

£12.99 with free tracked delivery, posted within 2 working days.

Radiator dosing tools compared

Ours against the usual L shape

OursThe usual 90° dosing tool
The last of the inhibitorRuns into the radiator down a 38° dropLies in the level pipe until you unscrew it
The funnel9 cm mouth, about 300 mlA tube you pour down
Radiator threadGenuine Flomasta brass, comes fitted, screws in by hand, spanner optionalBrass fitting

£12.99 with free tracked delivery, posted within 2 working days.

The details

The spec sheet

Fits
The 1/2 inch BSP plug port in the top corner of a radiator, the standard size on UK panel radiators
Funnel
9 cm across and 9 cm tall, holds about 300 ml
Radiator thread
Genuine Flomasta 1/2 inch BSP brass hexagon nipple
Made from
Black PLA and brass
Works with
Fernox F1, Sentinel X100 and any liquid inhibitor, cleaner or leak sealer that goes in through a radiator
In the box
Funnel, and the angled elbow with the genuine Flomasta brass end fitted
Delivery
Free tracked UK delivery, posted within 2 working days
Returns
14 days. Return postage is paid by the buyer

Inhibitor, answered

Common questions

Will it fit my radiator?

It fits the 1/2 inch BSP port in the top corner of a radiator, where the blanking plug or the bleed valve screws in. That is the standard size on UK panel radiators. Unscrew the plug and the elbow's brass end screws straight in.

Which inhibitors does it work with?

Any liquid central heating inhibitor that comes in a bottle, including Fernox F1 and Sentinel X100, and liquid cleaners and leak sealers that go in through a radiator. Use the dose on the bottle.

Do I have to drain the whole system?

No. Turn the heating off, close both valves on one radiator, bleed it and let a little water out of that radiator so there is room for the inhibitor. The rest of the system stays full.

Will it fit under my window sill?

The rim of the funnel sits about 11 cm above the plug port, so it fits under most sills and shelves above a radiator. The whole tool is 12.6 cm tall.

Why does the angle matter?

Most dosing tools turn 90 degrees into a level pipe. Once the tool is screwed into the radiator you can't tip it, so the last of the inhibitor sits in that pipe and drips down the radiator when you take it off. Ours drops at about 38 degrees all the way into the radiator, so it all runs in.

What about a combi boiler or sealed system?

It works the same way. When the radiator is back on, check the pressure gauge on the boiler and top it up from the filling loop if it has dropped.

How do I make the funnel point straight up?

Put a few wraps of PTFE tape on the brass and screw the elbow into the radiator by hand until it is snug and the socket points straight up (a spanner on the brass is optional). Then screw the funnel on.

Every drop in, £12.99

Protect the boiler. Keep the carpet dry.

Get every drop of inhibitor into the radiator for £12.99, with free tracked delivery and posted within 2 working days.

£12.99Free delivery Amazon